3
Gazebo Floor
FLOOR SYSTEM
ASSEMBLY CONTINUED
1
Step 1
Connects J1
to J1 with
3" screw.
Step 2
Connects J1
to J2 with
3" screws.
J1
J1
Notch up and
to the inside
J2
J2
J2
J2
J2
J1
J1
J2
J3
Approx.
1/8"
J2
Connects J2
to J3 with
3" screws.
10' Top View
Top View
10' Bottom View
Connect
with 3"
screws.
12' & 14' Top View
Connect with
(1) 3" screw down
inside with 6" Phillips Bit.
(Install after J1 and J2 are complete)
J2
J3
Note: Pre-drill Hole
in J2 at bottom
1-A
❑ 8 pcs. J1’s Treated 2 x 4 x 44-
3
/4”
❑ 8 pcs. J2’s Treated 2 x 4 x 54-
3
/4”
❑ 1 pc. J3 Solid Center Block 4 x 4 x 3-
1
/2”
PARTS LIST 10’ FLOOR KIT
Fig.1
Fig.2
Fig.3
Locate the center of the area in which you will be
setting up your Gazebo floor kit. Start with the J3
Center Block with the pre-drilled holes on top. Lay out
eight J2’s around block with the pre-drilled holes
facing downward as in FIG. 1 for 10’ Gazebo, see
Fig. 4 for 12’ and 14’ Models. Attach with one 3”
screw in each hole into J2’s maintaining
approximately 1/8” spacing between the J2’s and J3
Center Block.
Layout all J1 parts on edge with the notch facing upward
and inward at the end of the J2’s forming a circular type
pattern as shown in illustration above. Connect the J1’s to
J1’s as shown in Fig. 2 with one 3” screw. Be sure to keep
all joints even at top and outer edges at the angle joint.
Assemble remaining J1’s in this same manner except for
last pair of J1. Center the joint of the J1’s in the center of
the J2’s as shown in Fig. 2 and attach the J1 to the J2 with
two 3” screws as shown. Repeat this process to attach
remaining parts. You should then be able to carefully close
the final gap in the J1’s. You may need to adjust the gap
between J2 and J3 at this time.
1-A: Step 1
❑ 10 pcs. J1’s Treated 2 x 6 x 44-
3
/4”
❑ 10 pcs. J2’s Treated 2 x 6 x 67-
7
/8”
❑ 1 pc. J3 Hollow Center Block 6 x 6 x 5-
1
/2”
PARTS LIST 12’ FLOOR KIT
NOTE: Assembly shown below is for 10’ Gazebo floor kit.
The 12’ and 14’ Gazebo floor kit assembles in the same
manner; however, there are two extra J1’s, J2’s and Deck
Panels for the 12’ and there are four extra J1’s, J2’s and
Deck Panels for the 14’. Follow Instructions below for
assembly of the 10’, 12’ and 14’ floor kit.
1-A: Step 2
1-A: Step 3
IMPORTANT: Two people required for this step.
❑ 12 pcs. J1’s Treated 2 x 6 x 44-
3
/4”
❑ 12 pcs. J2’s Treated 2 x 6 x 81-
1
/16”
❑ 1 pc. J3 Hollow Center Block 8 x 8 x 5-
1
/2”
PARTS LIST 14’ FLOOR KIT
Fig.4
With all J2 boards secured to Center Block, carefully turn
the assembly over - 10’ Gazebo only and install one 3”
screw through each predrilled hole in J2’s into Center Block
as shown in Fig.5. You may have to remove Base Plate to
install screws from the bottom on the 10’ Gazebo Floor and
reinstall. If Installing a 12’ or 14’ Gazebo floor, do not turn
floor over. Install remaining 3” screws into Center Block with
6” bit supplied in kit as shown in Fig. 4.
Fig.5
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals